10K Gold Jewelry
10K Gold Jewelry Made to Order: Carton Cube, Duty and the Freight Line That Surprises - HOLYCOME
10K Gold Jewelry: tolerances, cost structure and the reject rule for US wholesale buyers.
Why the Made to Order Quote Looks Cheap Until It Lands
In November, a US buyer of 10K Gold Jewelry ordered 50 10K Gold Jewelry and asked for the same cast or hand-finished as a competitor's sample. What arrived matched the photo and missed the drawing, and 13 pieces had to be reworked at the buyer's expense, the figure being USD 56-400 for a 50-piece run.
Nothing in that rejection was exotic. At USD 56-400 per piece and 50 pieces on the order, a stamp accuracy rate of two percent is a costing error rather than a quality mystery.
Cost of the fix was about 21 seconds per piece. On 50 pieces that is a few hours at the bench and the whole claim file disappears, the figure being USD 56-400 for a 50-piece run.
The Made-to-Order Path for 10K Gold Jewelry
Made-to-order is a different production line, not a slower version of stock. It starts with a signed drawing, then a wax or resin model, then a casting, then setting, then finish, and each stage can fail on its own, which is USD 56-400 on the Made to Order schedule.
Twenty days is realistic for a new 10K Gold Jewelry when the model exists and only the stone changes. A new model adds a day for the CAD, a day for the print, and a day for the buyer to approve the render before metal is committed, which is USD 56-400 on the Made to Order schedule.
The risk sits in approval, not in the bench. A buyer who approves a render on a phone screen and rejects the casting has bought a prototype, not a product. We send the render at 1:1 scale with a millimetre grid for that reason, with IGI report and single-piece foam box stated on the same sheet.
What Fails First on 10K Gold Jewelry
alloy color drift
Two alloy lots of 14K rose can read peach and copper under the same light. Holding a master color chip per order keeps a collection coherent, and 50 pieces leaves Wuzhou in single-piece foam box at USD 56-400.
Our countermeasure is a gauge and a written limit. It adds about 21 seconds per piece and removes the defect from the run rather than from the carton, which is how the Made to Order account reads it at USD 56-400.
solder joint porosity
A sizing joint soldered with too much flux pits after polish and cracks in wear. Joint inspection belongs in the final QC, not the bench, shipped as single-piece foam box and certified IGI report.
In a 50-piece run this typically shows on 17 of pieces. Catching it means measuring assay within 0.3K of the stamp at the tray level, not inspecting the finished carton, shipped as single-piece foam box and certified IGI report.
stamp accuracy
A 14K stamp on 13.6K metal is a legal exposure, not a cosmetic one. Assay per lot is the only defensible check, which is USD 56-400 on the Made to Order schedule.
The commercial effect is refining loss plus a legal stamp correction, typically USD 15-28 per piece. Buyers who have seen it once put it in the purchase order; buyers who have not usually discover it on the first return, which the Made to Order file records at USD 56-400 in single-piece foam box.
The Measurements Behind a USD 56-400 Quote
Four numbers separate a 50-piece run that clears inspection from one that generates a credit note. None of them appears on the sample photo, shipped as single-piece foam box and certified IGI report.
| Spec point | Common trade output | HOLYCOME standard | Cost if missed |
|---|---|---|---|
| Clasp spring life | Sampled by hand | Cycled 500 times on a jig per lot | Detach claim and brand damage |
| Prong tension and seat depth | Checked by feel at the bench | Pull-tested per piece, seat depth written on the sheet | Stone loss and total replacement |
| Hallmark depth and placement | Stamped where it fits | Fixed position, depth measured so it never breaks the shank | Customs query and remaking |
| Solder flow at the joint | Not inspected | Joint inspected under 10x before setting | Crack at the seam in transit |
None of these are premium features. They cost seconds per piece and they remove the reason a buyer has to inspect twice, shipped as single-piece foam box and certified IGI report, quoted at USD 56-400 per piece in single-piece foam box.
MOQ, Samples and the Balance
The commercial frame is short enough to state in full. Minimum order is 50 pieces per design, and mixed designs travel in one shipment, so a 50-piece Made to Order order can carry three or four models without a separate setup charge. Sample pieces leave in 3-5 days when the components are in stock, and a new model adds about twenty days before the first article exists, priced at USD 56-400 for the 50-piece Made to Order run.
Payment is 30 percent with the order and 70 percent against the bill of lading, with the balance window stated on the invoice rather than agreed by message. Prices quoted at USD 56-400 are FOB Guangzhou or Shenzhen; DDP is quoted separately because the duty line moves with the tariff schedule and not with our cost.
Packing follows the single-piece foam box format at 50 pieces to the carton, and the packing list carries SKU, size and stone size so receiving can count without opening every box. Private-label cartons add three days for the print run and must be approved before the first bulk order, not after it, and at USD 56-400 for 50 pieces that is the number the buyer signs.
Certification is IGI report for the lots that carry it, with a batch report and per-piece measurement of assay within 0.3K of the stamp for the lots below the threshold. The document set travels with the shipping papers, which is what a customs broker asks for at the port rather than after clearance, and 50 pieces leaves Wuzhou in single-piece foam box at USD 56-400.
A rejected tray is settled inside the same order cycle against the retained reference piece. If the difference sits on our retained sample we replace or credit; if it appeared in transit we split the assay cost and file with the carrier, and that rule is written on the order before the deposit clears, which is how the Made to Order account reads it at USD 56-400.
What a USD 56-400 Quote Hides
The cost of a 10K Gold Jewelry in the USD 56-400 band splits roughly as below. The line buyers challenge most is labor, and it is the line that decides whether the piece survives a season.
| Cost line | Share | What moves it |
|---|---|---|
| Base metal or alloy for 10K Gold Jewelry | 34% | Alloy choice and casting yield |
| Stone or melee for 10K Gold Jewelry | 25% | Sieve range and lot batching |
| Setting and finishing labor for 10K Gold Jewelry | 22% | Jig design and bench minutes |
| Plating, polish and QC for 10K Gold Jewelry | 15% | Per-tray versus per-piece checks |
| Packaging for 10K Gold Jewelry | 4% | single-piece foam box |
If a supplier will not break out the five lines above, the number you are comparing is not a price. It is a total that somebody else assembled from assumptions, which is USD 56-400 on the Made to Order schedule.
What a Report Proves and What It Does Not
Buyers who have run three programs on 10K Gold Jewelry know this instinctively; first-time buyers learn it the expensive way, certified IGI report and packed single-piece foam box at 50 pieces.
Three numbers decide it for 10K Gold Jewelry: the tolerance band, the inspection density and the responsibility clause. Write all three down and the rest of the negotiation is arithmetic. Leave any of them out and it becomes a discussion about intent, on a 50-piece Made to Order order at USD 56-400.
We send a one-page sheet with every 10K Gold Jewelry quote that states those three, plus the retained-tray rule. Buyers who compare on it usually find that the gap between suppliers is smaller than the gap between the specs they were comparing, quoted at USD 56-400 per piece in single-piece foam box.
The Sample Approval That Survives Production
The short version for 10K Gold Jewelry: it is arithmetic, not relationship. The long version is below, certified IGI report and packed single-piece foam box at 50 pieces.
There is a version of this that looks cheaper on paper and costs more in practice: quoting the best case on 10K Gold Jewelry and letting the buyer discover the spread. It works once. The second order goes to whichever supplier quoted honestly, and at USD 56-400 for 50 pieces that is the number the buyer signs.
We would rather lose a first order of 10K Gold Jewelry on price than explain a defect after it lands. That position is unusual in this category and it is the reason our reorder share is high, which the Made to Order file records at USD 56-400 in single-piece foam box.
A 50-Piece Test Run
At 50 pieces inside single-piece foam box, the first order reads sell-through without betting the season on one model, which is how the Made to Order account reads it at USD 56-400.
Buyers who run that measurement before committing a season usually keep the supplier. Buyers who skip it usually pay twice for the same lesson, which the Made to Order file records at USD 56-400 in single-piece foam box.
The Dock Check on 10K Gold Jewelry
We ship from Guangzhou or Shenzhen and pick the port on the carrier rate, not on habit. IGI report travels with the shipping documents, and 50 pieces leaves Wuzhou in single-piece foam box at USD 56-400.
DDP removes the duty invoice that arrives after the carton clears, which matters on a first Made to Order order at USD 56-400.
Three steps at the dock: count against the packing list, weigh a sample tray, measure ten pieces. None needs a lab, and 50 pieces leaves Wuzhou in single-piece foam box at USD 56-400.
From Spec to single-piece foam box
The calendar below is what we quote on a 50-piece Made to Order run of 10K Gold Jewelry. It starts when the spec is signed, not when the deposit clears, quoted at USD 56-400 per piece in single-piece foam box.
- Sign the drawing at 1:1 scale with a millimetre grid, not a phone render.
- Cut the model in wax or resin and photograph it on the gauge before metal is committed.
- Cast the first article, set the stones and finish it exactly as bulk will be finished.
- Send the first article for approval with the weight and the stone measurements stated.
- Run the balance of the order in 25-30 days, holding the approved article as the reference.
- Ship with the approved article photographed beside a production piece from the same tray.
A first order of 50 pieces is a measurement, not a purchase. It tells you what assay within 0.3K of the stamp looks like from this bench, with IGI report and single-piece foam box stated on the same sheet, and at USD 56-400 for 50 pieces that is the number the buyer signs.
Frequently Asked Questions
Can you ship DDP?
DDP is available for US accounts and removes the duty invoice that arrives after the carton clears. FOB Guangzhou or Shenzhen is the default, and most buyers take DDP once and then switch after they see the breakdown, certified IGI report and packed single-piece foam box at 50 pieces.
How long does a reorder of the same 10K Gold Jewelry take?
With the model, the gauge set and the signed spec already in our system, a repeat is 12-15 days; a first run is 3-5 days for a stock-component sample and about 20 days when a new model is needed, and 50 pieces leaves Wuzhou in single-piece foam box at USD 56-400.
What finish do you use, and how thick is it?
Rhodium at 0.20 micron minimum on white 10K Gold Jewelry, with a palladium strike layer so wear-through reads white rather than yellow. Vermeil runs at 3 microns over sterling and is logged per lot, certified IGI report and packed single-piece foam box at 50 pieces.
How is 10K Gold Jewelry packed for single-piece foam box?
Every unit goes into a foam-backed pouch, then the single-piece foam box, then the outer carton at 50 pieces. The packing list carries the SKU, the size and the stone size so receiving can check without opening every box, which is USD 56-400 on the Made to Order schedule.
Can you ship DDP?
DDP is available for US accounts and removes the duty invoice that arrives after the carton clears. FOB Guangzhou or Shenzhen is the default, and most buyers take DDP once and then switch after they see the breakdown, certified IGI report and packed single-piece foam box at 50 pieces.
Next Step
If you are quoting 10K Gold Jewelry against another supplier, send that quote. We will mark the four lines where the numbers diverge and let you decide, quoted at USD 56-400 per piece in single-piece foam box.
The factory behind 10K Gold Jewelry here is Wuzhou HengliLai Jewelry Co., Ltd., operating since 2009 in Wuzhou, Guangxi, at roughly 60,000 pieces a month. Reach the export desk at service@holycome.com or +86 18078079070 on WhatsApp, and at USD 56-400 for 50 pieces that is the number the buyer signs.
Related reading: 10K Gold Jewelry Private Label Carton: Alloy, Karat and the Cost of a Color Change - HOLYCOME 10K Gold Jewelry Q4 Holiday Stock: Sample to Container: The Real Calendar - HOLYCOME
