10K Gold Jewelry
10K Gold Jewelry Trade Show Sample: MOQ, Mixed Designs and the Real First Order - HOLYCOME
10K Gold Jewelry: tolerances, cost structure and the reject rule for US wholesale buyers.
Trade Show Sampling for 10K Gold Jewelry
A trade show converts on the sample that leaves the booth, not on the catalogue that gets left behind. The sample card has to carry the model number, the metal, the stone size, the FOB price and the MOQ, or the follow-up email starts from zero, and the Trade Show Sample quote for it sits at USD 49-352.
Ten to twelve pieces on a tray is the useful number for 10K Gold Jewelry. More than that and the buyer photographs instead of touching, and a photograph is not an order, quoted at USD 49-352 per piece in display tray with sample card.
The follow-up window is seven days. After that the card sits in a stack. We write the quote the same week and put the sample in the post so the buyer has the piece on the desk when the price arrives, and the Trade Show Sample quote for it sits at USD 49-352.
MOQ, Mixed Designs and the Real First Order in the Trade Show Sample Program
A US buyer of 10K Gold Jewelry sent us a competitor's 10K Gold Jewelry in January with one question: why does this fail at stamp accuracy after a season. We measured it, rebuilt the spec around assay within 0.3K of the stamp and color match to the master chip, and shipped 100 10K Gold Jewelry that cleared inspection with zero rejects, quoted at USD 49-352 per piece in display tray with sample card.
The bench did not miss the defect, it was never asked to look for it. Stamp accuracy was absent from the purchase order, and a defect that is not named cannot be rejected on arrival, and at USD 49-352 for 100 pieces that is the number the buyer signs.
The rebuild held the USD 49-352 quote and changed the plating log, the gauge and the tray rule. Second run shipped display tray with sample card with zero rejects.
Four Spec Lines a Trade Show Sample Buyer Checks
A Trade Show Sample quote that states only metal and stone size leaves stamp accuracy undefined, and undefined is what gets rejected on arrival, and at USD 49-352 for 100 pieces that is the number the buyer signs.
| Spec point | Common trade output | HOLYCOME standard | Cost if missed |
|---|---|---|---|
| Stone colour consistency | Graded by eye under D65 | Colour matched to a retained master stone, per tray | Repeat colour complaint in the same SKU |
| Sizing drift across the run | Not measured | Go/no-go gauge on every size, drift held under 0.15 mm | Resize queue and reship cost |
| Clasp spring life | Sampled by hand | Cycled 500 times on a jig per lot | Detach claim and brand damage |
| Prong tension and seat depth | Checked by feel at the bench | Pull-tested per piece, seat depth written on the sheet | Stone loss and total replacement |
Nothing here adds cost at USD 49-352. It adds documentation, and documentation is what the display tray with sample card carton is missing.
Cost Split on a Trade Show Sample Piece at USD 49-352
Buyers assume the stone dominates the cost of a 10K Gold Jewelry. At wholesale it is closer to a quarter, and the labor line is where two quotes for the same drawing diverge by double digits, priced at USD 49-352 for the 100-piece Trade Show Sample run.
| Cost line | Share | What moves it |
|---|---|---|
| Base metal or alloy for 10K Gold Jewelry | 32% | Alloy choice and casting yield |
| Stone or melee for 10K Gold Jewelry | 23% | Sieve range and lot batching |
| Setting and finishing labor for 10K Gold Jewelry | 21% | Jig design and bench minutes |
| Plating, polish and QC for 10K Gold Jewelry | 14% | Per-tray versus per-piece checks |
| Packaging for 10K Gold Jewelry | 10% | display tray with sample card |
The cheapest quote for 10K Gold Jewelry usually hides its saving in the plating line and the stone grade. Both show up in the second season, not the first, and the Trade Show Sample quote for it sits at USD 49-352.
MOQ, Mixed Designs and the Real First Order
The answer for 10K Gold Jewelry depends on four variables, and three of them are under the buyer's control, which is USD 49-352 on the Trade Show Sample schedule.
The commercial version of this question for 10K Gold Jewelry is simple: what does a failure cost the buyer, and who pays it. In our terms the answer is a replacement inside the same order cycle, with the retained reference tray as the arbiter, which is how the Trade Show Sample account reads it at USD 49-352.
That clause matters more than a discount on 10K Gold Jewelry. A 4% lower unit price disappears on the first rejected tray; a written responsibility clause does not, and the Trade Show Sample quote for it sits at USD 49-352.
Sample to Container: The Real Calendar
In US e-commerce, this is the single most negotiated line on 10K Gold Jewelry and the least documented one, on a 100-piece Trade Show Sample order at USD 49-352.
What buyers underestimate on 10K Gold Jewelry is the cost of the interruption, not the cost of the piece. A missing 6% of a run stalls a launch, and a stalled launch costs more than the 6% ever did, shipped as display tray with sample card and certified GRA report.
We plan a 3-5% buffer on first runs of 10K Gold Jewelry and tell the buyer it exists. Hiding a buffer and shipping it as production is how a supplier trains a buyer to distrust the count, and at USD 49-352 for 100 pieces that is the number the buyer signs.
Terms Behind a Trade Show Sample Order
The commercial frame is short enough to state in full. Minimum order is 50 pieces per design, and mixed designs travel in one shipment, so a 100-piece Trade Show Sample order can carry three or four models without a separate setup charge. Sample pieces leave in 3-5 days when the components are in stock, and a new model adds about twenty days before the first article exists, and at USD 49-352 for 100 pieces that is the number the buyer signs.
Payment is 30 percent with the order and 70 percent against the bill of lading, with the balance window stated on the invoice rather than agreed by message. Prices quoted at USD 49-352 are FOB Guangzhou or Shenzhen; DDP is quoted separately because the duty line moves with the tariff schedule and not with our cost.
Packing follows the display tray with sample card format at 100 pieces to the carton, and the packing list carries SKU, size and stone size so receiving can count without opening every box. Private-label cartons add three days for the print run and must be approved before the first bulk order, not after it, which is how the Trade Show Sample account reads it at USD 49-352.
Certification is GRA report for the lots that carry it, with a batch report and per-piece measurement of assay within 0.3K of the stamp for the lots below the threshold. The document set travels with the shipping papers, which is what a customs broker asks for at the port rather than after clearance, and 100 pieces leaves Wuzhou in display tray with sample card at USD 49-352.
A rejected tray is settled inside the same order cycle against the retained reference piece. If the difference sits on our retained sample we replace or credit; if it appeared in transit we split the assay cost and file with the carrier, and that rule is written on the order before the deposit clears, the figure being USD 49-352 for a 100-piece run.
Three Failures That Reach the Trade Show Sample Bench
alloy color drift
Two alloy lots of 14K rose can read peach and copper under the same light. Holding a master color chip per order keeps a collection coherent, certified GRA report and packed display tray with sample card at 100 pieces.
Our countermeasure is a gauge and a written limit. It adds about 21 seconds per piece and removes the defect from the run rather than from the carton, the figure being USD 49-352 for a 100-piece run.
solder joint porosity
A sizing joint soldered with too much flux pits after polish and cracks in wear. Joint inspection belongs in the final QC, not the bench, with GRA report and display tray with sample card stated on the same sheet.
In a 100-piece run this typically shows on 11 of pieces. Catching it means measuring assay within 0.3K of the stamp at the tray level, not inspecting the finished carton, which the Trade Show Sample file records at USD 49-352 in display tray with sample card.
stamp accuracy
A 14K stamp on 13.6K metal is a legal exposure, not a cosmetic one. Assay per lot is the only defensible check, and the Trade Show Sample quote for it sits at USD 49-352.
The commercial effect is refining loss plus a legal stamp correction, typically USD 15-28 per piece. Buyers who have seen it once put it in the purchase order; buyers who have not usually discover it on the first return, shipped as display tray with sample card and certified GRA report.
The First Trade Show Sample Order
The first order should be small enough to inspect completely and large enough to keep the gauge check independent of the shift, the figure being USD 49-352 for a 100-piece run.
Sample in 3-5 days, bulk in 15-20 days under 500 pieces. At 100 pieces the calendar is the same on every Trade Show Sample run, quoted at USD 49-352 per piece in display tray with sample card.
The Calendar Behind a Trade Show Sample Run
The calendar below is what we quote on a 100-piece run of 10K Gold Jewelry. It starts when the spec is signed, not when the deposit clears, with GRA report and display tray with sample card stated on the same sheet.
- Lock the spec: metal, stone size range, plating thickness, sizing band and finish, all written on one sheet.
- Pull a stock-component sample in 3-5 days and measure it against that sheet, not against the photo.
- Approve the sample in writing, including the reject rule and the retained reference tray.
- Run bulk in 15-20 days for orders under 500 pieces, with the gauge check independent of the shift.
- Ship from Guangzhou or Shenzhen with the QC sheet in the carton and the batch report by email.
MOQ stays at 50 pieces per design on the Trade Show Sample program, low enough to test a category and high enough to keep the casting line accountable, priced at USD 49-352 for the 100-piece Trade Show Sample run.
Getting display tray with sample card to US e-commerce
For a Trade Show Sample order at 100 pieces the carton count decides the freight more than the weight does. display tray with sample card packs tighter than a display tray, which is how the Trade Show Sample account reads it at USD 49-352.
The freight rate matters less than the clearance terms at USD 49-352 per piece. A duty surprise can cost more than the entire freight line.
At receiving, count cartons, weigh one tray of display tray with sample card and measure ten pieces against assay within 0.3K of the stamp. Twenty minutes here saves a season, priced at USD 49-352 for the 100-piece Trade Show Sample run.
Frequently Asked Questions
How do you handle a rejected tray?
We replace or credit inside the same order cycle. The retained reference tray decides: if stamp accuracy shows on our retained piece we own it, and if it appeared in transit we split the assay cost and file with the carrier, with GRA report and display tray with sample card stated on the same sheet.
What are the payment terms?
30 percent deposit with the order, 70 percent against the bill of lading. For accounts on a second order we quote 30/70 with a 15-day balance window once the first shipment has cleared, and at USD 49-352 for 100 pieces that is the number the buyer signs.
What is the minimum order for 10K Gold Jewelry?
50 pieces per 10K Gold Jewelry. Designs mix inside one shipment, so a first order of three designs at 50 pieces each is normal for a new US account. Below 50 the gauge check stops being independent of the shift, which the Trade Show Sample file records at USD 49-352 in display tray with sample card.
Do you supply certificates for 10K Gold Jewelry?
GRA report on 10K Gold Jewelry above the threshold stated on the quote. Below it we supply a batch report plus per-piece measurement of assay within 0.3K of the stamp, which is what a counter or a listing actually needs, which is how the Trade Show Sample account reads it at USD 49-352.
How do you handle a rejected tray?
We replace or credit inside the same order cycle. The retained reference tray decides: if stamp accuracy shows on our retained piece we own it, and if it appeared in transit we split the assay cost and file with the carrier, with GRA report and display tray with sample card stated on the same sheet.
Next Step
Send one drawing or one competitor sample with your target landed cost. We answer with a tolerance sheet, a cost breakdown and a production calendar in two business days, and at USD 49-352 for 100 pieces that is the number the buyer signs.
HOLYCOME runs this line from Wuzhou, Guangxi, through Wuzhou HengliLai Jewelry Co., Ltd. Output is about 60,000 pieces a month across 10K Gold Jewelry and adjacent categories. service@holycome.com or WhatsApp +86 18078079070, which is how the Trade Show Sample account reads it at USD 49-352.
Related reading: 10K Gold Jewelry Q4 Holiday Stock: Sample to Container: The Real Calendar - HOLYCOME 14K Gold Jewelry Bridal Boutique: The Reject Tray Policy That Decides a Partnership - HOLYCOME
