Emerald Cut Moissanite AQL, Defect Classes and the Reject Rul for Amazon Sellers - HOLYCOME

Returns on Emerald Cut Moissanite are not a failure of trust. They are a process: a sampling plan, a defect class, a credit or remake rule, and a photo file. The buyers who lose the most money on Emerald Cut Moissanite are the ones who inspect nothing until the tray lands on their own desk.

When a Emerald Cut Moissanite order is wrong

Most Emerald Cut Moissanite disputes are not malice. They are a missing step: no approved first article, no final inspection photos, no sampling plan. A tray of Emerald Cut Moissanite pieces arriving with bent prongs, mismatched stones or bad plating is traceable to one of those skipped steps.

The fix is not to argue after delivery on a Emerald Cut Moissanite order. It is to put the sampling plan and the first-article approval in the order, so the defect stops at the bench, not at your warehouse.

Most Emerald Cut Moissanite disputes happen because the sample and the bulk differ. The sample is hand-finished; bulk runs on the bench. Approve the pre-production sample, not just the showroom sample, and photograph it beside the bulk piece.

The AQL sampling plan for Emerald Cut Moissanite

Use two levels on a Emerald Cut Moissanite lot. Critical defects — sharp prongs, loose stones, broken solder, wrong karat — sample to AQL 1.0. Finish defects — scratches, plating haze, off-shade stone — sample to AQL 2.5.

For a 500-piece Emerald Cut Moissanite lot, inspect 32 pieces. Up to 2 critical defects accepts the lot; 3 or more rejects it and the bench re-runs. Write this into the Emerald Cut Moissanite order so the rule is decided before the pieces ship.

Critical defects on Emerald Cut Moissanite are not negotiable: a sharp prong scratches the customer, a loose stone falls off, a broken clasp makes the piece unwearable. These accept zero defects in most channels.

Defect classes for Emerald Cut Moissanite

Define the Emerald Cut Moissanite classes in writing. Class A: piece cannot be sold (stone loose, prong sharp, broken clasp). Class B: piece is sellable after touch-up (light scratch, uneven polish). Class C: piece passes but should not repeat (minor plating unevenness).

Each class has a different action. Class A is remake or credit on the spot. Class B is touch-up before pack. Class C is logged for the next Emerald Cut Moissanite run. Without written classes, every defect becomes a negotiation.

Finish defects on Emerald Cut Moissanite are where AQL helps. A light scratch on the back of a ring is acceptable; a scratch on the face is not. Write the defect location into the acceptance rule, not just the count.

Red flags in Emerald Cut Moissanite returns

Three red flags on Emerald Cut Moissanite claims. First, a supplier who refuses to inspect before shipment. Second, a no-claims-after-delivery clause in the order. Third, a dispute settled by a partial credit without a photo file.

Hold the photo file. Every Emerald Cut Moissanite claim needs the PO, the approved first article, the batch number and the piece photo. Without it, the claim becomes a he-said-she-said with the freight.

The photo file is your claim. For every Emerald Cut Moissanite lot, keep the PO, the approved sample, the batch number, and photos of the first article, the bench and the final pack. A claim without this file is a negotiation, not a right.

The cost of a claim on Emerald Cut Moissanite

Numbers. A 500-piece Emerald Cut Moissanite lot with a 3 percent defect rate is 15 pieces. Re-making 15 pieces costs the factory roughly the labour of one run and stops the claim from reaching you.

A buyer who skips sampling on a Emerald Cut Moissanite lot and finds 15 percent defects at stocking loses two weeks of shelf time and the reorder window. The inspection step costs one working day; the failed Emerald Cut Moissanite lot costs a season.

When a claim lands, fix the root cause, not just the piece. A Emerald Cut Moissanite lot with three loose stones means the setting station pressure is wrong, not that three pieces were unlucky. Adjust the station before the next run.

Scaling returns from 50 to 500 Emerald Cut Moissanite pieces

At 50 Emerald Cut Moissanite pieces, a bad lot is annoying. At 500, a 3 percent defect rate is 15 pieces and a warehouse dispute. The sampling plan pays for itself the first time it catches a loose-stone batch before the container closes.

Repeat Emerald Cut Moissanite buyers run the same AQL every lot and keep the photo file. They rarely have a claim; the factory knows the rule in writing and the bench adjusts before packing.

Picture a 500-piece Emerald Cut Moissanite lot sampled at 32 pieces. Two loose stones in the sample means the whole lot goes back to the bench before shipping. The cost is three working days; the alternative is a warehouse that finds fifteen loose stones and a retail buyer who never orders again. The AQL step is unglamorous, but on Emerald Cut Moissanite it is the single cheapest insurance you have.

Your Emerald Cut Moissanite checklist

1. Approve the first Emerald Cut Moissanite article in writing before bulk.
2. Set AQL 1.0 for critical defects and 2.5 for finish defects.
3. Inspect 32 pieces on a 500-piece Emerald Cut Moissanite lot.
4. Define Class A, B and C defects in the PO.
5. Hold the balance until final photos match the approved sample.
6. Keep the photo file: PO, batch number, piece photo.
7. Log Class C findings so the next Emerald Cut Moissanite run does not repeat them.

Frequently Asked Questions

What is the reject rule for a Emerald Cut Moissanite bulk order?

Sample the final Emerald Cut Moissanite lot under AQL 1.0 for critical defects (sharp prongs, loose stones, broken solder) and 2.5 for finish defects. A sample size of 32 pieces at a 500-piece lot is the common starting point. The sampling plan and defect classes are written into every Emerald Cut Moissanite PO.

Who pays for defective Emerald Cut Moissanite pieces?

The factory, if the defect is a workmanship deviation from the approved sample. Send photos, the PO number and the approved sample reference. We credit the next Emerald Cut Moissanite order or re-make the shortfall; we do not charge the buyer for our bench error. The sampling plan and defect classes are written into every Emerald Cut Moissanite PO.

How do I prevent a Emerald Cut Moissanite claim before it ships?

Approve the first article in writing, ask for pre-production photos, and hold the balance until final inspection photos match the approved sample. Most Emerald Cut Moissanite disputes come from skipping the first-article step, not from the bench. The sampling plan and defect classes are written into every Emerald Cut Moissanite PO.

Can I return stock that simply does not sell?

No. Emerald Cut Moissanite made to your design, size and metal is not returnable. What we can do is re-design the piece, exchange the stock for a new design, or split the run into a smaller first batch. Order 50 Emerald Cut Moissanite pieces, prove the sell-through, then scale. The sampling plan and defect classes are written into every Emerald Cut Moissanite PO.

What if a stone falls out after six months at retail?

Send the piece back with the wearer story. On a Emerald Cut Moissanite piece set by our bench, prong failure within the warranty window is a remake or credit. We ask for the retail photos so we can also improve the setting station before the next Emerald Cut Moissanite run. The sampling plan and defect classes are written into every Emerald Cut Moissanite PO.

Returns on Emerald Cut Moissanite are a process, not a dispute. The sampling plan, the defect classes and the photo file turn a bad lot into a credit or a remake, and stop it from reaching your retail customer.

Related Reading

• More Emerald Cut Moissanite wholesale guides from HOLYCOME
• Ask the HOLYCOME bench about a Emerald Cut Moissanite order

Next Step

Send us the approved Emerald Cut Moissanite sample, and we write the AQL sampling plan, the defect classes and the credit rule into the order. Inspection photos land on your desk before the balance is released.

HOLYCOME inspects every Emerald Cut Moissanite lot under AQL before it ships, and keeps the first article, the batch number and the inspection photos for six months. A defect from our bench is remade or credited, not argued. We have run this since 2009 in Wuzhou. Trade desk: service@holycome.com, WhatsApp +86 18078079070.

Every Emerald Cut Moissanite lot HOLYCOME ships is sampled under AQL before it leaves Wuzhou, and the photo file travels with the carton. Since 2009 we have treated a claim as a bench fix, not a dispute: remakes are credited on the next Emerald Cut Moissanite order, and the setting station is adjusted before re-run.

A Emerald Cut Moissanite lot is controlled before it ships, not after. Approve the first article, sample to AQL 1.0 for critical defects, define Class A B and C in the PO, and hold the balance on inspection photos. The photo file turns a Emerald Cut Moissanite claim from a dispute into a credit.

Send us the approved Emerald Cut Moissanite sample. We write the AQL sampling plan, the defect classes and the credit rule into the PO, and send inspection photos before the balance is released.