Solid Gold Jewelry
Solid Gold Jewelry Made to Order: Carton Cube, Duty and the Freight Line That Surpris - HOLYCOME
Solid Gold Jewelry: tolerances, cost structure and the reject rule for US wholesale buyers.
Carton Cube, Duty and the Freight Line That Surprises Buyers
Last June, a US buyer of solid Gold Jewelry placed 50 solid Gold Jewelry against a sample signed in October. The first container landed with 9 pieces that failed on stamp accuracy alone, and USD 30-115 landed on the buyer's P&L before a single unit sold, shipped as single-piece foam box and certified IGI report.
Nobody on that bench was careless. They were working to a spec that existed only in a photograph, and stamp accuracy is what a photograph fails to define, on a 50-piece Made to Order order at USD 56-400.
The fix cost about 21 seconds per solid Gold Jewelry and removed the credit note entirely. That is the whole economics of a spec sheet, and it is why we write one on every quote, with IGI report and single-piece foam box stated on the same sheet, the figure being USD 56-400 for a 50-piece run.
The Made-to-Order Path for solid Gold Jewelry
Made-to-order is a different production line, not a slower version of stock. It starts with a signed drawing, then a wax or resin model, then a casting, then setting, then finish, and each stage can fail on its own, which is how the Made to Order account reads it at USD 56-400.
Twenty days is realistic for a new solid Gold Jewelry when the model exists and only the stone changes. A new model adds a day for the CAD, a day for the print, and a day for the buyer to approve the render before metal is committed, which is how the Made to Order account reads it at USD 56-400.
The risk sits in approval, not in the bench. A buyer who approves a render on a phone screen and rejects the casting has bought a prototype, not a product. We send the render at 1:1 scale with a millimetre grid for that reason, quoted at USD 56-400 per piece in single-piece foam box.
The Three Failures We See Most in Incoming Samples
alloy color drift
Two alloy lots of 14K rose can read peach and copper under the same light. Holding a master color chip per order keeps a collection coherent, shipped as single-piece foam box and certified IGI report.
In a 50-piece run this typically shows on 14 of pieces. Catching it means measuring assay within 0.3K of the stamp at the tray level, not inspecting the finished carton, shipped as single-piece foam box and certified IGI report.
solder joint porosity
A sizing joint soldered with too much flux pits after polish and cracks in wear. Joint inspection belongs in the final QC, not the bench, and the Made to Order quote for it sits at USD 56-400.
The commercial effect is refining loss plus a legal stamp correction, typically USD 15-28 per piece. Buyers who have seen it once put it in the purchase order; buyers who have not usually discover it on the first return, which is USD 56-400 on the Made to Order schedule.
stamp accuracy
A 14K stamp on 13.6K metal is a legal exposure, not a cosmetic one. Assay per lot is the only defensible check, which is how the Made to Order account reads it at USD 56-400.
Our countermeasure is a gauge and a written limit. It adds about 21 seconds per piece and removes the defect from the run rather than from the carton, and at USD 56-400 for 50 pieces that is the number the buyer signs.
What US buyers Check Before They Sign
Four lines decide whether solid Gold Jewelry at USD 56-400 sells through or comes back, and none of them appears on a typical trading-company quote.
| Spec point | Common trade output | HOLYCOME standard | Cost if missed |
|---|---|---|---|
| Clasp spring life | Sampled by hand | Cycled 500 times on a jig per lot | Detach claim and brand damage |
| Prong tension and seat depth | Checked by feel at the bench | Pull-tested per piece, seat depth written on the sheet | Stone loss and total replacement |
| Hallmark depth and placement | Stamped where it fits | Fixed position, depth measured so it never breaks the shank | Customs query and remaking |
| Solder flow at the joint | Not inspected | Joint inspected under 10x before setting | Crack at the seam in transit |
Put these four into the purchase order and the Made to Order argument after delivery becomes arithmetic, on a 50-piece Made to Order order at USD 56-400.
Order Terms, Sample Timing and Packing
The commercial frame is short enough to state in full. Minimum order is 50 pieces per design, and mixed designs travel in one shipment, so a 50-piece Made to Order order can carry three or four models without a separate setup charge. Sample pieces leave in 3-5 days when the components are in stock, and a new model adds about twenty days before the first article exists, certified IGI report and packed single-piece foam box at 50 pieces.
Payment is 30 percent with the order and 70 percent against the bill of lading, with the balance window stated on the invoice rather than agreed by message. Prices quoted at USD 56-400 are FOB Guangzhou or Shenzhen; DDP is quoted separately because the duty line moves with the tariff schedule and not with our cost.
Packing follows the single-piece foam box format at 50 pieces to the carton, and the packing list carries SKU, size and stone size so receiving can count without opening every box. Private-label cartons add three days for the print run and must be approved before the first bulk order, not after it, and 50 pieces leaves Wuzhou in single-piece foam box at USD 56-400.
Certification is IGI report for the lots that carry it, with a batch report and per-piece measurement of assay within 0.3K of the stamp for the lots below the threshold. The document set travels with the shipping papers, which is what a customs broker asks for at the port rather than after clearance, shipped as single-piece foam box and certified IGI report.
A rejected tray is settled inside the same order cycle against the retained reference piece. If the difference sits on our retained sample we replace or credit; if it appeared in transit we split the assay cost and file with the carrier, and that rule is written on the order before the deposit clears, and at USD 56-400 for 50 pieces that is the number the buyer signs.
Where USD 56-400 Per Piece Actually Goes
Cost per piece at USD 56-400 leaves little room for assumption. The table shows which line compresses and which one only moves quality.
| Cost line | Share | What moves it |
|---|---|---|
| Base metal or alloy for solid Gold Jewelry | 30% | Alloy choice and casting yield |
| Stone or melee for solid Gold Jewelry | 20% | Sieve range and lot batching |
| Setting and finishing labor for solid Gold Jewelry | 19% | Jig design and bench minutes |
| Plating, polish and QC for solid Gold Jewelry | 12% | Per-tray versus per-piece checks |
| Packaging for solid Gold Jewelry | 19% | single-piece foam box |
A factory with no bench minutes per piece has never costed solid Gold Jewelry at USD 56-400. Ask for minutes and for the reject rule.
What a Report Proves and What It Does Not
Ask three suppliers of solid Gold Jewelry this question and you will get three answers. Only one of them survives an inspection, priced at USD 56-400 for the 50-piece Made to Order run.
Three numbers decide it for solid Gold Jewelry: the tolerance band, the inspection density and the responsibility clause. Write all three down and the rest of the negotiation is arithmetic. Leave any of them out and it becomes a discussion about intent, priced at USD 56-400 for the 50-piece Made to Order run.
We send a one-page sheet with every solid Gold Jewelry quote that states those three, plus the retained-tray rule. Buyers who compare on it usually find that the gap between suppliers is smaller than the gap between the specs they were comparing, and the Made to Order quote for it sits at USD 56-400.
The Sample Approval That Survives Production
On solid Gold Jewelry, the difference between a 40-day order and a 90-day order is usually two signatures, not a factory delay, certified IGI report and packed single-piece foam box at 50 pieces.
There is a version of this that looks cheaper on paper and costs more in practice: quoting the best case on solid Gold Jewelry and letting the buyer discover the spread. It works once. The second order goes to whichever supplier quoted honestly, priced at USD 56-400 for the 50-piece Made to Order run.
We would rather lose a first order of solid Gold Jewelry on price than explain a defect after it lands. That position is unusual in this category and it is the reason our reorder share is high, on a 50-piece Made to Order order at USD 56-400.
What This Means for a First Order
A first Made to Order order of 50 pieces per design at USD 56-400 is a test of the line, not a commitment to the range.
Ask for the retained tray and the batch report with the first shipment. Both are free and both decide the second order, which is USD 56-400 on the Made to Order schedule.
Freight, Duty and the Arrival Check
Export runs through Guangzhou or Shenzhen. Air freight lands in 5-8 days on the US west coast and 7-10 on the east, certified IGI report and packed single-piece foam box at 50 pieces, shipped as single-piece foam box and certified IGI report.
For a first order, DDP matters more than the freight rate. The surprise is the duty line, not the per-kilo charge, the figure being USD 56-400 for a 50-piece run.
Check the count, the weight and assay within 0.3K of the stamp and color match to the master chip before the carton goes to the shelf. Twenty minutes at receiving saves a season of returns, shipped as single-piece foam box and certified IGI report, and the Made to Order quote for it sits at USD 56-400.
How a Repeat Order Gets Built
The sequence below is fixed for a Made to Order run. The dates move with the stone lot, not with the shipping season, certified IGI report and packed single-piece foam box at 50 pieces.
- Sign the drawing at 1:1 scale with a millimetre grid, not a phone render.
- Cut the model in wax or resin and photograph it on the gauge before metal is committed.
- Cast the first article, set the stones and finish it exactly as bulk will be finished.
- Send the first article for approval with the weight and the stone measurements stated.
- Run the balance of the order in 25-30 days, holding the approved article as the reference.
- Ship with the approved article photographed beside a production piece from the same tray.
Reorders inside this sequence run 12-15 days, because the model and the gauge set stay here after the Made to Order shipment, quoted at USD 56-400 per piece in single-piece foam box.
Frequently Asked Questions
Can you ship DDP?
DDP is available for US accounts and removes the duty invoice that arrives after the carton clears. FOB Guangzhou or Shenzhen is the default, and most buyers take DDP once and then switch after they see the breakdown, with IGI report and single-piece foam box stated on the same sheet.
How long does a reorder of the same solid Gold Jewelry take?
With the model, the gauge set and the signed spec already in our system, a repeat is 12-15 days; a first run is 3-5 days for a stock-component sample and about 20 days when a new model is needed, shipped as single-piece foam box and certified IGI report.
What finish do you use, and how thick is it?
Rhodium at 0.20 micron minimum on white solid Gold Jewelry, with a palladium strike layer so wear-through reads white rather than yellow. Vermeil runs at 3 microns over sterling and is logged per lot, shipped as single-piece foam box and certified IGI report.
How is solid Gold Jewelry packed for single-piece foam box?
Every unit goes into a foam-backed pouch, then the single-piece foam box, then the outer carton at 50 pieces. The packing list carries the SKU, the size and the stone size so receiving can check without opening every box, which is how the Made to Order account reads it at USD 56-400.
Can you ship DDP?
DDP is available for US accounts and removes the duty invoice that arrives after the carton clears. FOB Guangzhou or Shenzhen is the default, and most buyers take DDP once and then switch after they see the breakdown, with IGI report and single-piece foam box stated on the same sheet.
Next Step
The next step is a sample in 3-5 days, not a container. Write to service@holycome.com or WhatsApp +86 18078079070 and mark it Made to Order, which the Made to Order file records at USD 56-400 in single-piece foam box.
HOLYCOME is operated by Wuzhou HengliLai Jewelry Co., Ltd., a factory in Wuzhou, Guangxi, producing since 2009 at roughly 60,000 pieces a month. Contact service@holycome.com or WhatsApp +86 18078079070, priced at USD 56-400 for the 50-piece Made to Order run.
Related reading: Solid Gold Jewelry Private Label Carton: Alloy, Karat and the Cost of a Color Change - HOLYCOME Solid Gold Jewelry Q4 Holiday Stock: Sample to Container: The Real Calendar - HOLYCOME
